新疆石油天然气 ›› 2026, Vol. 22 ›› Issue (3): 104-111.DOI: 10.12388/j.issn.1673-2677.2026.03.010

• 油气开发 • 上一篇    下一篇

超高温压裂液可控破胶技术研究进展

张杨, 张世岭   

  1. 中国石油集团工程技术研究院有限公司,北京  102266

  • 收稿日期:2026-07-30 修回日期:2026-08-20 接受日期:2026-09-01 出版日期:2026-09-15 发布日期:2026-09-15
  • 通讯作者: 张世岭(1990—),2021年毕业于中国石油大学(北京)化学工程与技术专业,博士,高级工程师,主要从事油田化学及储层改造方向研究。(E-mail)zsljames@163.com
  • 作者简介:张杨(1985—),2012年毕业于东北石油大学油气井工程专业,硕士,高级工程师,主要从事储层改造研究。(E-mail)zhangyangdri@cnpc.com.cn
  • 基金资助:

    1.国家科技重大专项“油气田地质力学与储层改造新技术”(2025ZD14014);

    2.中国石油天然气集团有限公司科技项目“相变立体支撑体积压裂新技术研究”(2025DJ105)。

Research Progress of Controllable Breaking Technology for Ultra-High-Temperature Fracturing Fluids

Zhang Yang, Zhang Shiling   

  1. CNPC Engineering Technology R&D Company Limited,Beijing 102266,China

  • Received:2026-07-30 Revised:2026-08-20 Accepted:2026-09-01 Online:2026-09-15 Published:2026-09-15

摘要:

深层、超深层油气藏压裂施工对压裂液耐温、耐盐、抗剪切、携砂和压后返排性能提出更高要求。针对“耐高温”与“超高温”概念交叉使用的问题,以150 ℃以上压裂环境作为讨论范围,重点关注180~200 ℃及以上条件下破胶剂提前分解、有效作用时间缩短和裂缝深部破胶不足等问题。围绕超高温压裂液可控破胶技术,梳理胍胶(瓜尔胶)及改性胍胶、聚丙烯酰胺类压裂液、清洁压裂液、滑溜水和海水基体系的破胶对象与破胶难点,比较氧化破胶、酶破胶、酸/热破胶、包覆缓释和复合破胶的适用边界。超高温压裂场景中的破胶控制,不宜仅以压后快速降黏为目标,还应兼顾施工阶段黏度保持、破胶剂在目标位置的有效释放、聚合物充分降解以及破胶后低伤害返排。后续评价可进一步建立高温高压动态释放、残留形态与导流能力保持之间的对应关系,为深层、超深层油气藏低伤害压裂液体系设计提供依据。

关键词:

超高温压裂液, 可控破胶, 过硫酸盐, 包覆破胶剂, 聚丙烯酰胺, 低伤害评价

Abstract:

Deep and ultra-deep oil and gas reservoirs have stricter requirements on the thermal resistance,salt tolerance,shear resistance,proppant-carrying capacity and post-fracturing cleanup of fracturing fluids. Given the cross uses of the two concepts “high-temperature” and “ultra-high-temperature”,this research discusses fracturing environments above 150 ℃,with particular attention to the premature decomposition,shortened effective reaction time and insufficient degradation in deep fractures of breakers at 180-200 ℃ and higher temperature. The targets and technical difficulties of breakers are summarized for guar and modified guar fluids,polyacrylamide-based fluids,viscoelastic surfactant fluids,slick-water and seawater-based systems,and the application boundaries of oxidative,enzymatic,acid/thermal,encapsulated-release and composite breakers are compared. Controllable breaking should not be limited to rapid viscosity reduction after fracturing,but should coordinate viscosity retention during pumping,effective breaker release at target locations,sufficient polymer degradation and low-damage flowback after breaking. Subsequent assessment can identify the correlation among high-temperature high-pressure dynamic release,retention morphology and fracture conductivity retention to provide references for design of low-damage fracturing fluid systems for deep and ultra-deep oil and gas reservoirs.

Key words:

ultra-high-temperature fracturing fluid, controllable breaking, persulfate, encapsulated breaker, polyacrylamide, low-damage evaluation

中图分类号: