Key Parameter Optimization Study of Managed Pressure Drilling in Slim-Hole Horizontal Wells
Managed pressure drilling (MPD) technology in slim-hole horizontal wells has gradually gained widespread applications in oil and gas development. However,balancing bottomhole pressure control and wellbore cleanup remains a challenge when drilling in formations with a narrow density window. To address this issue,this paper proposes a method based on the genetic algorithm combined with dual physical constraints,to optimize key parameters such as the drilling fluid density,rheology,flow rate,drillpipe rotation speed,and wellhead backpressure. Through global optimization,the method controls the increment of equivalent circulating density (ECD),significantly improves wellbore cleanup,expands the allowable range of drilling fluid density,and reduces the probability of complex drilling incidents. Engineering case validation shows that the optimized design aligns well with field applications,resulting in significant improvements in both drilling efficiency and wellbore safety. The findings of this research provide theoretical support and practical guidance for broader applications of MPD in slim-hole horizontal wells.
The Influence Law of Temperature-Pressure Coupling Effect on the Mechanical Properties of Cement Stone
To address the unclear mechanical response mechanisms of the cement sheath in deep oil and gas well cementing under complex temperature-pressure conditions,this study systematically investigated the coupled effects of curing temperature,curing pressure,testing temperature,and confining pressure on the mechanical properties of Class G oil-well cement. Specimens were prepared at different curing temperatures ranging from 25°C to 140°C and curing pressures of the atmospheric pressure and 21.7 MPa. Triaxial compression tests were then conducted at different testing temperatures from 25°C to 140°C and confining pressures from 0 to 20 MPa to analyze the evolution of stress-strain curves,peak stresses,and elastic moduli. The results show that increasing curing temperature reduces the peak stress and elastic modulus of the set cement,while high-pressure curing significantly inhibits pore development and improves structural compactness. Increasing testing temperature helps enhance the mechanical performance of cement at the testing temperature close to its curing temperature. Increasing confining pressure improves the plasticity and residual strength of cement,and the cement exhibits staged evolutionary characteristics under different coupled conditions. The findings of this study provide a theoretical basis and experimental support for the design of cement slurry systems and the integrity evaluation of cement sheaths in deep formations.
An Optimization Method for CO2 Water-Alternating-Gas (WAG) Development Strategy Driven by Machine Learning
Cuttings Transport Mechanisms in Slimhole Horizontal Wells Considering Drill String Eccentricity
The narrow annulus in slimhole horizontal wells leads to significant differences in Cuttings transport,compared to conventional horizontal wells. To investigate the cutting transport mechanisms in slimhole horizontal wells,a CFD-based numerical model accounting for drill string eccentricity was developed for solid-liquid two-phase flow in the annulus. This study analyzed the effects of key factors,including flow rates,drill pipe rotation speeds,well inclination angles,and drilling fluid properties,on cutting transport in slimhole horizontal wells. The results showed that increasing the drill pipe rotation speed enhances the tangential and axial velocities of the annular fluid and expands the "viscous coupling" region. This facilitates the upward movement of cuttings from the lower side to the upper side of the annulus,thereby improving transport efficiency. Critical thresholds for "rotation speeds" and "flow rates" were identified in highly inclined sections,where cutting transport becomes the most challenging with the two parameters both below the thresholds,and in horizontal sections,where transport becomes more difficult with the two parameters both exceeding the thresholds. Increasing the drilling fluid density enhances the buoyancy acting on cuttings and reduces deposition. The effects of drilling fluid rheological parameters on wellbore cleanup exhibit non-linear trends,with an optimal range existing under different flow rates and rotation speeds. The findings of this research provide theoretical support for optimizing hydraulic parameters in slimhole horizontal wells and preventing issues like drill string sticking.
Significant casing deformation (CD) occurs during multi-stage fracturing of shale gas horizontal wells,which reduces the ratio of recovered reservoirs and increases operation costs. Based on a comprehensive review of global research on this issue,a comparative analysis of the current status of casing deformation in shale gas horizontal wells was conducted. With the casing deformation data from Changning-Weiyuan,Luzhou,and Weirong blocks,the distribution patterns of casing deformation in terms of time,space,and morphology were summarized. The influences of engineering factors such as casing and cement sheath types,cementing quality,fracturing and perforation parameters,and thermal stresses,as well as geological factors such as reservoir heterogeneity and reservoir slip,on casing deformation,were analyzed. The analysis results indicate that while engineering factors can increase casing stresses,they are unlikely to cause casing deformation. Among geological factors,reservoir slip induced by natural fractures and faults activated during multi-stage fracturing is the main controlling factor leading to significant casing deformation. To address this issue,various control methods were summarized,including optimizing casing and cement sheath parameters,improving cementing quality,selecting appropriate fracturing and perforation parameters,optimizing wellbore trajectory,and controlling reservoir slip. Additionally,it was proposed to enhance the understanding of formations and improve prediction accuracy of reservoir slip. The research findings provide references for casing integrity design and control during the fracturing process.
With the extensive applications of new technologies such as zipper fracturing in shale oil and gas development,the casing is subjected to both the multi-stage cyclic internal pressure and the external non-uniform compressive load caused by zipper fracturing operations. Given this,this paper analyzes the variation law of casing collpase strength under multi-stage cyclic load and zipper fracturing of platform wells via the multi-stage cyclic load experiments and numerical simulations. The calculation method of the casing comprehensive collapse strength coefficient under multi-stage fracturing is developed and applied to a casing-deformed well in Xinjiang Oilfield. The results show that the casing collapse strength decreases linearly with the number of load cycles under cyclic loading. Zipper fracturing results in the non-uniform stress distribution around the well,and the casing collapse strength nearly linearly decreases with the increasing stress non-uniformity. Under the combined effects of internal and external loads,the casing collapse strength drops by more than 15%,which increases risks of casing deformation. The calculation method of casing callopase strength in platform wells proposed in this paper provides calculation guidance for the prevention of casing deformation in fracturing practice.
Tight oil reservoirs are widely distributed in China,with a large proportion of reserves and great development potential. These reservoirs have low matrix permeability and porosity,with fractures acting as main oil and gas flow channels,and gas injection is often used to recover such reservoirs. However,due to the cross-scale development of reservoir fractures and the influence of reservoir heterogeneity and viscous fingering,the technology of gas injection to improve oil recovery has limits. Gas channeling can easily occur in the presence of fractures and high permeability bands,causing many issues related to the energy supplement of formation. In this paper,foam and CO2-responsive gel were selected to prepare the gas channeling and sweep control system,and their performance and applicability in tight oil reservoirs were evaluated by physical experiment simulation. Commercial numerical simulation software was used to characterize CO2 huff-n-puff and underground gelling reaction. Through the numerical simulation of a tight oil reservoir in China,it is proved that the CO2-responsive gel has an obvious stimulation effect during huff-n-puff treatment,resulting in an increase in recovery rate by 3.1%. This research validates the promising application prospects of the CO2-responsive gel system in the development of tight oil reservoirs.
Nonlinear Propagation and Influencing Factors of Perforation Detonation Waves in Ultra-Deep Wells
As oil and gas wells are gradually extended to deep and ultra-deep layers,the safety of completion strings during perforation has attracted more attention. Based on the principles of computational fluid dynamics,a perforated interval-packer detonation wave propagation model was established,revealing the detonation wave propagation and reflection rules in the wellbore completion fluid and clarifying the characteristics of the influence of completion fluid on detonation wave propagation. Research shows that the detonation wave propagation process demonstrates extremely strong non-periodicity and irregularity. When the detonation wave propagates to the packer position,the amplitude of the detonation wave pressure is reduced by up to 75.65%. The detonation reflected waves show better periodicity,and the amplitude of the detonation pressure waves is reduced by 23.4% when it propagates to the perforated interval. The density of the completion fluid not only has a great influence on the amplitude of the detonation waves during propagation,but also has a great interference on the waveform characteristics of the detonation waves. The viscosity of the completion fluid has almost no impact on the waveform characteristics of the detonation waves during propagation,and has a small impact on the amplitude of the detonation waves. With the impact of detonation waves on the completion string considered only,priority should be given to selecting a completion fluid system with low density and high viscosity to reduce the impact of detonation waves on the downhole completion string. The research results of this article provide a reference for the design of on-site completion fluid parameters for oil and gas wells.
Performance Evaluation of the Cement Sheath in Jimsar Shale Oil Wells
Hydraulic fracturing technology is an important method for increasing the production capacity of shale oil wells. The mechanical behavior of well cement sheath during fracturing has an important impact on the safety and efficiency of production. Based on the cement slurry system in Jimsar region,a cement specimen maintenance mold was designed as well as a cement bonding strength test program,maintaining the standard cylindrical specimen of cement and the set cement bond specimen. The uni/triaxial compression experiments were then carried out as well as the cyclic loading experiments and bonding strength experiments under simulated well bottom conditions to investigate the rules governing damage and destruction of cement bodies and cementing interface. The results show that under uniaxial compression,the set cement has significant elastic-brittle characteristics and that macroscopic cracks are formed in the cement body when it is damaged.The average Young's modulus of cement is 3.054 GPa and the average Poisson's ratio is 0.127. Under triaxial conditions,the strength and plasticity of the cement sheath are enhanced. During cyclic loading,there is a bilinear accumulation of cementite plastic deformation,with the amount of plastic deformation being positively correlated with the peak load. The plastic strain after 20 cycles increased from 0.24% to 2.46% when the peak load increased from 22.7 MPa to 53.2 MPa. The cement bonding strength is lower than 1 MPa,which is much lower than the body strength,and the bonding interface is a natural mechanical weak zone,representing a risk point for wellbore seal failure.
Simulation and Countermeasures of Casing Erosion at Downhole Decoupled Sandblaster During Fracturing
During long-time fracturing,the high speed proppant-carrying fluid flowing will cause serious erosion for downhole tools and casings. Therefore,it is important to understand the flow field distribution inside the tool and the casing erosion pattern during fracturing,propose improvement measures,optimize fracturing parameters,and protect wellbore integrity. A finite element mechanical model of casing erosion at the decoupled sandblaster during fracturing was developed,and a systematic analysis and study of erosion in an ultra-deep well was conducted. The results show that without sheath protection,the erosion rate of the casing at the outlet reaches 1.46×10-3 kg/(m2·s),with a casing thickness reduction of 1.35 mm,which decreases the casing strength,and the pipe string with erosion defect is more prone to stress concentration. After the sheath is added,the wall thickness reduction of the casing caused by erosion is significantly lower than that of the working condition without sheath protection. The finite element model developed allows a complete and quantitative study and analysis on all the points near the outlet of the sandblaster. The safety window of wall thickness thinning of the eroded sheath under different injection rate of fracturing fluid and proppant ratio was predicted. The safety window can quantitatively provide guidance for the operators to ensure effective protection of the casings and prevent casing erosion by controlling the injection rate and proppant ratio. The study is of great significance to parameter optimization and wellbore protection during fracturing.