In view of technical challenges of lost circulation control during ultra-deep drilling,this research provides a systematic review of lost circulation materials (LCMs) for ultra-deep drilling,covering both international and China’s research progress. It summarizes the advantages and limitations of various types of LCMs,analyzes the core technical challenges under extreme wellbore environments,and outlines future development directions. As oil and gas exploration in China progressively advances toward ultra-deep formations,drilling operations are commonly confronted with complex conditions including high temperature and high pressure,multi-scale fracture-vug development,and dynamic in-situ stress disturbances. Frequent lost circulation,difficulty in thief zone plugging,and short sealing duration have severely constrained the efficient development of ultra-deep hydrocarbon resources. At present,a multi-category technological framework for ultra-deep LCMs has been established,encompassing rigid bridging materials,consolidating materials,micro/nano-plugging agents,smart-responsive materials,and multifunctional composite systems,with notable progress achieved in lost circulation control. However,existing technologies still face critical challenges,such as insufficient long-term stability at ultra-high temperature (>220 ℃),inadequate sealing strength for large-scale vugs and fractures,and unclear understanding of lost circulation control mechanisms. For the future,smart-responsive materials,nanocomposites,and green and high-efficiency materials represent the core directions for breakthroughs. Furthermore,in-depth studies on multi-field coupled plugging mechanisms and the development of dedicated evaluation standards for ultra-deep drilling conditions are urgently required. These efforts will underpin the safe and efficient development of ultra-deep oil and gas resources.
Well SDTK-1 is China's first 10,000 m ultra-deep scientific exploration well with extremely complex downhole conditions. Its fourth and fifth casing sections are 10,000 m level deep and confronted with world class cementing challenges,including ultra-high temperature,multi-pressure systems,active oil,gas and water zones,lost circulation in fractured vuggy thief zones,and long irregular open hole sections. Conventional cementing materials,processes and supporting tools for ultra-deep wells fail to adapt themselves to the extreme operating conditions of this well. Aiming at three core engineering difficulties,namely sidetracking after drill string failure in the fourth casing section,cementing of the 10,000 m ultra-deep fifth casing section,and zonal isolation of oil,gas and water zones under a near-zero safe density window,this research combines laboratory research and full process field operation data to systematically analyze the technical bottlenecks of high strength cement plugs for sidetracking the fourth casing interval,managed-pressure cementing for the Φ206.38 mm liner in the fourth casing section,and composite zonal cementing via direct injection and reverse squeezing for the Φ139.7 mm liner in the fifth casing section. Four developed original technologies are fully elaborated,namely the high precision sidetracking cement plug technology for 10,000 m wells,multi-point dynamic ECD fine managed-pressure cementing technology,ultra-high temperature cement slurry system resistant to 240°C,and the direct injection and reverse squeezing zonal cementing process for 10,000 m wells. Field application results show that the overall cementing qualification rate of the fourth liner section reaches 82.5%,an Asian record of the deepest cementing operation with Φ206.38 mm casing. The overall cementing qualification rate of the fifth liner section hits 92.9%,and the qualification rate of barriers sealing hydrocarbon zones is 100%,establishing a new global record of the deepest liner cementing. The proposed technologies can provide critical theoretical references and practical engineering experience for cementing projects of 10,000 m level ultra-deep wells in China.
In drilling of deep,ultra-deep,and unconventional oil and gas reservoirs,formation pressure anomaly leads to frequent formation-wellbore fluid influxes,resulting in annual non-productive time of over 2,000 rig-days. This highlights the urgent need for high-precision early kick detection methods. This study develops a mechanistic-data hybrid,three-stage kick identification framework based on the processes of “encountering abnormal pressure zones-fluid influx into the wellbore-surface return of oil and gas.” Sensitive parameters are selected using Pearson correlation coefficients and employed in a random forest model to identify abnormal pressure zones;multiphase flow physical models are used to constrain wellbore engineering parameters,and a long short-term memory (LSTM) network is used to predict the gas migration within the wellbore;surface return is monitored using an XGBoost model based on flow rate and total pit volume. A lag-time feature system is established from 293 kick events to improve early detection in complex wellbore intervals. The three-stage identification framework and the incorporation of physical constraints enhance model consistency,and the lag-time feature strategy improves generalizability. The proposed approach provides a practical and reliable solution for intelligent kick monitoring and early warning in drilling operations.
Drilling fluid performance degradation and downhole tool failure,induced by high formation temperature,have become critical challenges restraining safe and efficient implementation of ultra-deep drilling. Wellbore drilling fluid temperature control is an essential technology to deal with high formation temperature. This research systematically reviews the research progress of wellbore drilling fluid temperature control technologies for ultra-deep drilling worldwide. First,the evolution of wellbore heat transfer models from steady-state models and transient models to multiphysics coupled models is analyzed,and the development of numerical simulation methods and intelligent prediction technologies is summarized. Subsequently,the development status of active cooling equipment for drilling fluids,structures and materials of insulated drill pipes,and continuous circulation technologies is reviewed,with emphasis on their temperature control mechanisms and application performance. Finally,the challenges to existing temperature control technologies in terms of adaptability to complex ultra-deep well conditions,equipment reliability,and system-level coordinated control are discussed,and future development directions of wellbore drilling fluid temperature control technologies for ultra-deep drilling are proposed.
Key Parameter Optimization Study of Managed Pressure Drilling in Slim-Hole Horizontal Wells
Managed pressure drilling (MPD) technology in slim-hole horizontal wells has gradually gained widespread applications in oil and gas development. However,balancing bottomhole pressure control and wellbore cleanup remains a challenge when drilling in formations with a narrow density window. To address this issue,this paper proposes a method based on the genetic algorithm combined with dual physical constraints,to optimize key parameters such as the drilling fluid density,rheology,flow rate,drillpipe rotation speed,and wellhead backpressure. Through global optimization,the method controls the increment of equivalent circulating density (ECD),significantly improves wellbore cleanup,expands the allowable range of drilling fluid density,and reduces the probability of complex drilling incidents. Engineering case validation shows that the optimized design aligns well with field applications,resulting in significant improvements in both drilling efficiency and wellbore safety. The findings of this research provide theoretical support and practical guidance for broader applications of MPD in slim-hole horizontal wells.
The Jimsar shale oil reservoir is characterized by ultra-low porosity,ultra-low permeability,low crude oil mobility and high reservoir heterogeneity. Consequently,the development of hydraulically fractured horizontal wells is challenged by reservoir energy depletion and unclear oil-water distribution. To address these issues,a hydraulic fracture propagation model coupled with a reservoir numerical simulation model based on the reservoir petrophysical properties is established to investigate the dynamic evolution of three fields (the pressure field,stress field,and oil saturation field) during hydraulic fracturing and subsequent production. The results indicate that the oil saturation around the fractures decreases rapidly after fracturing fluid injection,and it partially recovers during the early production stage,owing to flowback of fracturing fluids and spontaneous imbibition displacement. During hydraulic fracturing,the pressure and minimum horizontal principal stress around the wellbore both increase significantly,whereas they decrease during the production stage. The pressure decline near the wellbore is larger than that in the far-field region,while the reduction in near-wellbore minimum horizontal principal stress is relatively smaller because of the stress concentration induced by fracture opening. The combined effects of fracture opening and fracturing fluid injection result in the deflection of the in-situ stress orientation around the wellbore. This deflection weakens during the early production period but intensifies after long-term production. The findings of this research provide theoretical guidance for understanding the multi-field coupled evolution around horizontal wells during shale oil development and offer a scientific basis for improving the efficiency of shale oil exploitation.
Deep-well well-control monitoring systems record multiple parameters using unified timestamps;however,synchronous acquisition does not imply synchronous response to a kick. Owing to wellbore propagation,sensor location,signal accumulation,and measurement-chain effects,effective anomaly information from different parameters may occur at different historical positions. To address this issue,50 independent simulation cases were generated by inverting field operating-condition boundary parameters. The optimal response position of each parameter was identified within a historical window to construct time-corrected inputs. The same Transformer time-series model was then used to compare four input schemes. The combined input achieved the best overall performance,with Accuracy,Precision,Recall,and F1 values of 0.886,0.922,0.794,and 0.798,respectively. Relative to the synchronous input,Accuracy,Precision,Recall,and F1 changed by +0.025,+0.059,-0.019,and +0.019,respectively,with Precision showing the largest positive improvement. The confidence intervals for all four paired differences crossed zero,indicating a numerical improvement trend rather than statistical significance at the current sample scale. The non-matched input performed less favorably overall,demonstrating that the improvement mainly arose from correctly matching each parameter to its historical response position. Time-lag analysis improves the temporal alignment of input features and can serve as a data-quality optimization method for intelligent well control.
Temporary plugging fracturing,which activates natural fractures through hydraulic shearing and creates “self-supported” fracture systems derived from the shear dilation,has now become a key technical pathway for constructing volumetric geothermal reservoirs in hot dry rock. This research systematically reviews the research progress of temporary plugging-shearing fracturing technology for hot dry rock from two dimensions,namely laboratory simulation tests and representative engineering practices of enhanced geothermal systems (EGS). Existing physical simulation methods mostly assume constant normal loads,with insufficient high temperature adaptability and multi-field coupling simulation capacity,which leads to failure to truly reproduce the entire reservoir reconstruction process of deep hot dry rock. Current numerical simulations remain in a state of partial coupling and local matching,and a coupled model fully reproducing the whole temporary plugging-shearing process is still absent. Fewer high temperature shear constitutive models are available. Moreover,most of such models are modified from room-temperature models,and the constitutive model that couples shearing and seepage under real-time high temperature conditions is still absent. Finally,three core future research directions are proposed,including constructing a large-scale multi-field coupled physical simulation platform under constant normal stiffness conditions,developing numerical simulation methods for the full-process coupling of temporary plugging-shearing,and establishing a discrete fracture network (DFN) modeling framework constrained by multi-source data.
Deep fractured shale formations have well-developed fractures and weak cementation,and are prone to wellbore collapse. Adding anti-collapse agents to drilling fluid is an important way to improve the anti-collapse performance of drilling fluids and stabilize fractured shale. However,the existing anti-collapse agent has insufficient bonding effect at high temperature for borehole wall supporting and thus,difficulties in improving the overall mechanical strength of rock. Using amino acids containing benzene rings and cationic amino acids as raw materials,a high-temperature resistant and strong-bonding anti-collapse agent with temperature switching behavior was synthesized by amidation reaction. This agent delivers an intelligent behavior of “being dispersed and non-adhesive at low temperature,and yet softened and highly cementitious at high temperature”. The laboratory evaluation results show that the anti-collapse agent can increase the shale rolling recovery to 105.6% at 200 °C and the compressive strength of the shale core by 105.82%;in the drilling fluid system,it presents high compatibility and delivers effective sand bed cementation. The microscopic analysis show that the benzene ring and the amino group in the anti-collapse agent molecules present multiple cation-π interactions. The molecular cohesion is dominant at room temperature,while the adhesion to the external interface is weak. In the high temperature environment,the intermolecular cation-π bond is partially dissociated,the adsorption group is released and combined with the shale surface,to fill and cement micro-fractures,construct the tight and hydrophobic protective film,and ultimately effectively stabilize the wellbore. The findings of this research provide references for the design of high-performance water-based drilling fluids for deep fractured formations.
Deep and ultra-deep oil and gas reservoirs have stricter requirements on the thermal resistance,salt tolerance,shear resistance,proppant-carrying capacity and post-fracturing cleanup of fracturing fluids. Given the cross uses of the two concepts “high-temperature” and “ultra-high-temperature”,this research discusses fracturing environments above 150 ℃,with particular attention to the premature decomposition,shortened effective reaction time and insufficient degradation in deep fractures of breakers at 180-200 ℃ and higher temperature. The targets and technical difficulties of breakers are summarized for guar and modified guar fluids,polyacrylamide-based fluids,viscoelastic surfactant fluids,slick-water and seawater-based systems,and the application boundaries of oxidative,enzymatic,acid/thermal,encapsulated-release and composite breakers are compared. Controllable breaking should not be limited to rapid viscosity reduction after fracturing,but should coordinate viscosity retention during pumping,effective breaker release at target locations,sufficient polymer degradation and low-damage flowback after breaking. Subsequent assessment can identify the correlation among high-temperature high-pressure dynamic release,retention morphology and fracture conductivity retention to provide references for design of low-damage fracturing fluid systems for deep and ultra-deep oil and gas reservoirs.
In the development of the hydrothermal geothermal reservoir in Xiong'an City,the engineering challenge of unstable setting of whipstock slips is found in applications of the sidetracking multilateral well technology using flexible drilling tools,due to the special process requirements of setting in open-hole intervals. As a key geothermal reservoir,the mechanical properties of the Wumishan Formation dolomite of the Jixian System play a crucial role in the implementation of the ultra-short radius horizontal well technology for open-hole sidetracking with flexible drilling tools. In view of the insufficient exploration in existing studies of the variation law of the mechanical properties of dolomite under the in-situ temperature and soaking conditions of the hydrothermal layer,this research,through laboratory experiments,systematically studies the changes in the water content of dolomite with soaking time at different temperatures,as well as the influences of high-temperature soaking on mechanical properties of dolomite,such as compressive and tensile strengths. The results show that the water content of dolomite increases rapidly within 24 hours during high-temperature water soaking and tends to be stable after 120 hours,and the water content at 60°C is slightly higher than that at 20°C. Negative correlations are found between the water content and the compressive strength,tensile strength and elastic modulus. Owing to soaking,the macroscopic failure pattern of dolomite exhibits a transition from brittle to ductile failure. The SEM results further reveal a change in the failure mechanism from transgranular to intergranular failure. This research provides an important theoretical basis for the study of the mechanical properties of dolomite in geothermal reservoirs under soaking conditions and the wellbore stability during the setting of flexible drilling tools with the open-hole whipstocks,and is of great significance for the efficient development of geothermal resources in Xiong'an.
For vibratory-impact (vibro-impact) drilling,a highly efficient method for breaking deep hard rock,its rock breaking performance relies on the rock response characteristics under dynamic excitation,particularly the achievement of resonance. The damping and gravitational properties of rock significantly influence resonant behaviors,and yet their role within rock vibration models remains poorly defined. To address this,this research established a micro-vibration model incorporating gravitational and damping characteristics of rock,derived corresponding vibration equations,and employed analytical methods alongside Fourier series approximations to systematically investigate the dynamic properties and response patterns of rock under free vibration and periodic non-harmonic impact. Results indicate that natural frequencies of rock increase with stiffness but decrease with rising damping coefficients and density. Resonance occurs when the external excitation frequency equals the natural frequency of rock,with peaking of displacement responses. Damping effects delay responses and reduce resonance amplitudes,while rock density positively influences resonance intensity. Among impact parameters,increased static loads or reduced dynamic impact amplitudes diminish resonance effects. Finite element simulation results substantially align with theoretical analysis results,validating the reliability of the established model. The findings of this research provide a theoretical foundation for revealing rock breaking mechanisms in vibro-impact drilling and guidance for the design of vibro-impact tools and the optimization of field practice.
To address the problems such as wellbore instability,lost circulation of drilling fluids,and insufficient pressure-bearing capacity of existing plugging agents during deep well drilling,due to well-developed micro fractures in strata,a high temperature resistant organic-inorganic composite pressure-bearing plugging agent (P-ANDS) based on modified SiO2 was prepared through the water solution polymerization method. The structure and particle size of P-ANDS were characterized by Fourier transform infrared spectroscopy,thermogravimetric analysis,and laser particle size analysis. The results showed that the functional groups of each monomer were successfully grafted onto the surface of modified SiO2,forming a stable organic-inorganic composite structure;the initial thermal decomposition temperature of P-ANDS reached 270°C,indicating good thermal stability;the particle size was mainly distributed between 1-30 μm. Performance tests revealed that P-ANDS has excellent temperature and salinity resistance;the sand bed plugging performance test indicated that P-ANDS has good plugging ability for sand beds composed of particles of different mesh numbers;the pressure-bearing plugging performance test showed that P-ANDS,in contrast to traditional plugging materials,can form a stable pressure-bearing plugging layer in micro fractures. It was concluded that P-ANDS combines the flexible filling ability of organic materials and the rigid supporting ability of inorganic materials to significantly enhance the pressure-bearing plugging capacity of water-based drilling fluids in strata with well-developed micro fractures. It has a promising application prospect in complex deep wells with high temperature,high salinity,and well-developed micro fractures in strata.